Я обновился с 13.04 до 13.10, и у меня был установлен драйвер AX88179 из PPA .
Когда я обновил, преобразователь USB 3.0 в Ethernet перестал работать, хотя он должен быть включен в основную ветку ядра, начиная с 3.9. Он распознается системой, но соединение не устанавливается.
Вот соответствующий подробный вывод lsusb
:
Bus 004 Device 006: ID 0b95:1790 ASIX Electronics Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x0b95 ASIX Electronics Corp.
idProduct 0x1790
bcdDevice 1.00
iManufacturer 1 ASIX Elec. Corp.
iProduct 2 AX88179
iSerial 3 00000000000001
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 57
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 124mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 0
iInterface 4 Network_Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 11
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 3
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 22
bNumDeviceCaps 2
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000002
Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 1 micro seconds
bU2DevExitLat 101 micro seconds
Device Status: 0x000c
(Bus Powered)
U1 Enabled
U2 Enabled
В отличие от в этом вопросе устройство больше не распознается как устройство Ethernet. Вот соответствующий вывод dmseg:
dmesg | grep ASIX
[ 3.238120] usb 4-2: Manufacturer: ASIX Elec. Corp.
[ 61.907446] usb 4-2: Manufacturer: ASIX Elec. Corp.
[ 84.772115] usb 4-1: Manufacturer: ASIX Elec. Corp.
[ 192.615236] usb 4-2: Manufacturer: ASIX Elec. Corp.
[ 1146.200351] usb 4-2: Manufacturer: ASIX Elec. Corp.
dmesg | grep AX88179
[ 3.238119] usb 4-2: Product: AX88179
[ 61.907444] usb 4-2: Product: AX88179
[ 84.772110] usb 4-1: Product: AX88179
[ 192.615231] usb 4-2: Product: AX88179
[ 1146.200346] usb 4-2: Product: AX88179
Драйвер не устанавливается после обновления, насколько я знаю.
Драйвер работает просто отлично, если Ubuntu не перейдет в спящий режим. После выхода из сна водитель просто перестает работать.
Единственный обходной путь, который я нашел, - это отключить режим сна.
Я установил ppa:
add-apt-repository ppa:qji/ax88179
# since there is no source for soucy, replace it with raring:
sed s/saucy/raring/g /etc/apt/sources.list.d/qji-ax88179-saucy.list>/etc/apt/sources.list.d/qji-ax88179-raring.list
rm /etc/apt/sources.list.d/qji-ax88179-saucy.list
aptitude update
aptitude install ax88179
reboot
Он работал один раз , только в первый раз после первой перезагрузки. с тех пор я получаю ошибки в системном журнале. Это работает на ноутбуке моего друга, хотя, с параболой Linux. Я куплю другой адаптер;)