У меня есть машина, работающая Кармический, который встраивается в большой экран. Когда я работаю xrandr -q
, это сообщает, что вывод VGA соединен, даже когда нет никакого присоединенного экрана. Это вызывает некоторые проблемы с другим связанным с разрешением программным обеспечением (что я не могу измениться в данный момент).
Существует ли способ отключить вывод VGA так, чтобы он не обнаруживался вообще или был там, некоторые фиксируют, я могу бэкпортировать так, чтобы он больше не сообщал неправильно? Некоторая информация о системе ниже. Насколько я могу сказать, что это происходит только на этих аппаратных средствах.
Screen 0: minimum 320 x 200, current 1360 x 864, maximum 4096 x 4096
VGA connected 1360x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm
1360x768 59.8*
1152x864 60.0
1024x768 60.0
800x600 60.3
640x480 59.9
LVDS connected 1152x864+0+0 (normal left inverted right x axis y axis) 0mm x 0mm
1920x1080 60.0 +
1680x1050 84.9 74.9 69.9 60.0
1600x1024 60.2
1400x1050 85.0 74.8 70.0 60.0
1280x1024 85.0 75.0 60.0
1440x900 59.9
1280x960 85.0 60.0
1360x768 59.8
1152x864 100.0 85.1 85.0 75.0 75.0 70.0 60.0*
1024x768 85.0 75.0 70.1 60.0
832x624 74.6
800x600 85.1 72.2 75.0 60.3 56.2
640x480 85.0 72.8 75.0 59.9
720x400 85.0
640x400 85.1
640x350 85.1
TV disconnected (normal left inverted right x axis y axis)
00:02.0 VGA compatible controller: Intel Corporation Mobile GME965/GLE960 Integrated Graphics Controller (rev 03)
Subsystem: Micro-Star International Co., Ltd. Device 8030
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 27
Region 0: Memory at fe900000 (64-bit, non-prefetchable) [size=1M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at c000 [size=8]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0100c Data: 4191
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Kernel modules: i915
00:02.1 Display controller: Intel Corporation Mobile GME965/GLE960 Integrated Graphics Controller (rev 03)
Subsystem: Micro-Star International Co., Ltd. Device 8030
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at fe800000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
После добавления
Option "monitor-VGA" "VGA"
в раздел «Device» вашего xorg.conf добавьте следующий раздел «Monitor»:
Section "Monitor"
Identifier "VGA"
Option "Ignore" "True"
EndSection
Это скажет X игнорировать выход.