Ой andTainted G для загрузки адаптера DVB

Кто-либо может консультировать по вопросам ООП и Испорченного сбоя? Выполнение 3.16.0-4-amd64 ядра и загруженного media_build от v4L и других приложений. Но обе из 1. Новинки Hauppage WinTV TD500 и 2. PCTV 292e не удаются загрузиться с ООП и Испорченными комментариями, сопровождаемыми дампом отслеживания стека для входа./dev/dvb/... не создается также. Только сбой TD500, включенный в ниже журнала для ясности. Повторно применили все приложения и загружающийся без оборудования устройства все прекрасные загрузки ОС. И работа отлично и непрерывно в течение почти 2 лет на более старом ядре (2013) так не аппаратные средства. Все встроенные микропрограммные обеспечения развернутый штраф и драйвер загружаются хорошо.

Я не вижу примечания этой проблемы больше нигде. Прежде чем я черт возьми, все далеко и запускают снова кого-либо, смогу предложить что это, возможно, постараться не повторять ошибку?

'May  3 20:20:45 ledzep3 kernel: [    5.915054] sd 2:0:0:0: [sda] Attached SCSI disk
May  3 20:20:45 ledzep3 kernel: [    5.976960] usb 2-1: New USB device found, idVendor=2040, idProduct=8400
May  3 20:20:45 ledzep3 kernel: [    5.984968] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
May  3 20:20:45 ledzep3 kernel: [    5.992290] usb 2-1: Product: WinTV Nova-DT
May  3 20:20:45 ledzep3 kernel: [    5.998524] usb 2-1: Manufacturer: Hauppauge
May  3 20:20:45 ledzep3 kernel: [    6.004632] usb 2-1: SerialNumber: 4035120147
May  3 20:20:45 ledzep3 kernel: [    6.376060] tsc: Refined TSC clocksource calibration: 1862.098 MHz
May  3 20:20:45 ledzep3 kernel: [    6.692076] usb 3-1: new full-speed USB device number 2 using uhci_hcd
May  3 20:20:45 ledzep3 kernel: [    6.869108] usb 3-1: New USB device found, idVendor=058f, idProduct=9254

May  3 20:20:45 ledzep3 kernel: [   12.085906] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
May  3 20:20:45 ledzep3 kernel: [   12.098974] lpc_ich: Resource conflict(s) found affecting gpio_ich
May  3 20:20:45 ledzep3 kernel: [   12.119568] leds_ss4200: no LED devices found
May  3 20:20:45 ledzep3 kernel: [   12.150143] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
May  3 20:20:45 ledzep3 kernel: [   12.217753] iTCO_vendor_support: vendor-support=0
May  3 20:20:45 ledzep3 kernel: [   12.218313] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
May  3 20:20:45 ledzep3 kernel: [   12.218349] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS
May  3 20:20:45 ledzep3 kernel: [   12.291929] Adding 6155260k swap on /dev/sda3.  Priority:-1 extents:1 across:6155260k SSFS
May  3 20:20:45 ledzep3 kernel: [   12.311691] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
May  3 20:20:45 ledzep3 kernel: [   13.189391] media: Linux media interface: v0.10
May  3 20:20:45 ledzep3 kernel: [   13.320840] dvb-usb: found a 'Hauppauge Nova-TD-500 (84xxx)' in cold state, will try to load a firmware
May  3 20:20:45 ledzep3 kernel: [   13.328646] usb 2-1: firmware: direct-loading firmware dvb-usb-dib0700-1.20.fw
May  3 20:20:45 ledzep3 kernel: [   13.335781] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw'
May  3 20:20:45 ledzep3 kernel: [   13.548240] dib0700: firmware started successfully.
May  3 20:20:45 ledzep3 kernel: [   14.060212] dvb-usb: found a 'Hauppauge Nova-TD-500 (84xxx)' in warm state.
May  3 20:20:45 ledzep3 kernel: [   14.069479] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
May  3 20:20:45 ledzep3 kernel: [   14.077218] DVB: registering new adapter (Hauppauge Nova-TD-500 (84xxx))
May  3 20:20:45 ledzep3 kernel: [   14.086638] usb 2-1: media controller created
May  3 20:20:45 ledzep3 kernel: [   14.160001] PGD 0
May  3 20:20:45 ledzep3 kernel: [   14.160001] Oops: 0002 [#1] SMP
May  3 20:20:45 ledzep3 kernel: [   14.160001] Modules linked in: dvb_usb_dib0700(O+) dib9000(O) dib7000m(O) dib0090(O) dib0070(O) dib3000mc(O) dibx000_common(O) dvb_usb(O) dvb_core(O) rc_core(O) media(O) iTCO_wdt iTCO_vendor_support dcdbas joydev lpc_ich mfd_core coretemp kvm serio_raw i2c_i801 rng_core i3000_edac shpchp edac_core floppy(+) evdev processor thermal_sys loop nf_conntrack_pptp nf_conntrack_proto_gre nf_conntrack fuse parport_pc ppdev lp parport autofs4 ext4 crc16 mbcache jbd2 crc32c_generic btrfs xor raid6_pq sr_mod cdrom sg hid_generic usbhid hid sd_mod crc_t10dif crct10dif_generic crct10dif_common ata_generic psmouse ata_piix radeon libata scsi_mod i2c_algo_bit ttm drm_kms_helper drm i2c_core tg3 ptp pps_core libphy uhci_hcd button ehci_pci ehci_hcd usbcore usb_common
May  3 20:20:45 ledzep3 kernel: [   14.160001] CPU: 0 PID: 237 Comm: systemd-udevd Tainted: G           O  3.16.0-4-amd64 #1 Debian 3.16.7-ckt25-1
May  3 20:20:45 ledzep3 kernel: [   14.160001] Hardware name: Dell Inc.                 PowerEdge SC440              /0YH299, BIOS 1.3.0  03/28/2007
May  3 20:20:45 ledzep3 kernel: [   14.160001] task: ffff88007c184390 ti: ffff88007c2e0000 task.ti: ffff88007c2e0000
May  3 20:20:45 ledzep3 kernel: [   14.160001] RIP: 0010:[<ffffffff81513080>]  [<ffffffff81513080>] __mutex_lock_slowpath+0xb0/0x1c0
May  3 20:20:45 ledzep3 kernel: [   14.160001] RSP: 0018:ffff88007c2e38c0  EFLAGS: 00010286
May  3 20:20:45 ledzep3 kernel: [   14.160001] RAX: 0000000000000000 RBX: ffff880079f96478 RCX: 0000000000000000
May  3 20:20:45 ledzep3 kernel: [   14.160001] RDX: 0000000000000000 RSI: ffff88007c1843f8 RDI: ffff880079f9647c
May  3 20:20:45 ledzep3 kernel: [   14.160001] RBP: ffff88007c2e3910 R08: 000000000000005d R09: ffff88007b3f1068
May  3 20:20:45 ledzep3 kernel: [   14.160001] R10: 0000000000000013 R11: 0000000000000014 R12: ffff880079f9647c
May  3 20:20:45 ledzep3 kernel: [   14.160001] R13: ffff88007c184390 R14: 00000000ffffffff R15: ffff880079f96480
May  3 20:20:45 ledzep3 kernel: [   14.160001] FS:  00007fb9f6703880(0000) GS:ffff88007fc00000(0000) knlGS:0000000000000000
May  3 20:20:45 ledzep3 kernel: [   14.160001] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
May  3 20:20:45 ledzep3 kernel: [   14.160001] CR2: 0000000000000000 CR3: 00000000366fe000 CR4: 00000000000007f0
May  3 20:20:45 ledzep3 kernel: [   14.160001] Stack:
May  3 20:20:45 ledzep3 kernel: [   14.160001]  ffff880079f96480 0000000000000000 ffff880079f963f0 ffff88007b3f1068
May  3 20:20:45 ledzep3 kernel: [   14.160001]  ffff880079f96408 ffff880079f96478 ffff880079f96000 ffff880079f96478
May  3 20:20:45 ledzep3 kernel: [   14.160001]  ffffffffa06787a0 00000000000000ff ffff880079f963f0 ffffffff815131ab
May  3 20:20:45 ledzep3 kernel: [   14.160001] Call Trace:
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff815131ab>] ? mutex_lock+0x1b/0x2a
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffffa064015e>] ? media_device_register_entity+0x7e/0x200 [media]
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff812b60a2>] ? vsnprintf+0x3d2/0x5c0
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff812b9c36>] ? kvasprintf+0x66/0x80
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff812b9c8e>] ? kasprintf+0x3e/0x40
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffffa0665760>] ? dvb_create_tsout_entity+0xd0/0x160 [dvb_core]
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffffa0665d59>] ? dvb_register_device+0x569/0x7d0 [dvb_core]
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffffa06675c8>] ? dvb_dmxdev_init+0xf8/0x140 [dvb_core]
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffffa068da5c>] ? dvb_usb_adapter_dvb_init+0x1bc/0x2d0 [dvb_usb]
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffffa068cba6>] ? dvb_usb_device_init+0x5b6/0x890 [dvb_usb]
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff8151319e>] ? mutex_lock+0xe/0x2a
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffffa06b7993>] ? dib0700_probe+0x63/0x110 [dvb_usb_dib0700]
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffffa00190dc>] ? usb_probe_interface+0x1cc/0x320 [usbcore]
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff813a4e7d>] ? driver_probe_device+0x9d/0x3d0
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff813a527b>] ? __driver_attach+0x8b/0x90
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff813a51f0>] ? __device_attach+0x40/0x40
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff813a2f7b>] ? bus_for_each_dev+0x5b/0x90
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff813a4510>] ? bus_add_driver+0x180/0x250
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff813a59cb>] ? driver_register+0x5b/0xe0
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffffa00179cc>] ? usb_register_driver+0x7c/0x150 [usbcore]
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffffa06dc000>] ? 0xffffffffa06dbfff
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff8100213c>] ? do_one_initcall+0xcc/0x200
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff810db34d>] ? load_module+0x210d/0x26f0
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff810d6fb0>] ? store_uevent+0x40/0x40
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff810dba8d>] ? SyS_finit_module+0x7d/0xa0
May  3 20:20:45 ledzep3 kernel: [   14.160001]  [<ffffffff81514a0d>] ? system_call_fast_compare_end+0x10/0x15
May  3 20:20:45 ledzep3 kernel: [   14.160001] Code: 00 8b 03 85 c0 78 09 31 c0 87 03 83 f8 01 74 72 48 8b 43 10 4c 8d 7b 08 48 89 63 10 41 be ff ff ff ff 4c 89 3c 24 48 89 44 24 08 <48> 89 20 4c 89 6c 24 10 eb 21 66 0f 1f 44 00 00 49 c7 45 00 02
May  3 20:20:45 ledzep3 kernel: [   14.160001]  RSP <ffff88007c2e38c0>
May  3 20:20:45 ledzep3 kernel: [   14.160001] CR2: 0000000000000000
May  3 20:20:45 ledzep3 kernel: [   14.638780] ---[ end trace cfe04fa841e68257 ]---
May  3 20:20:45 ledzep3 kernel: [   14.844056] floppy0: no floppy controllers found
May  3 20:20:45 ledzep3 kernel: [   14.948247] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
May  3 20:20:45 ledzep3 kernel: [   18.305021] tg3 0000:03:00.0 eth1: Link is up at 1000 Mbps, full duplex
May  3 20:20:45 ledzep3 kernel: [   18.308221] tg3 0000:03:00.0 eth1: Flow control is off for TX and off for RX'
    May