Looked at other configuration Q&A about eth0 and wlan0. Nothing suggested seemed to work. Running 14.04 Lubuntu on desktop, and puppyLinux on client laptop.
frank@HP-Pavilion:~$ ifconfig
"eth0 Link encap:Ethernet HWaddr: 00:18:f3:31:19:d6
UP BROADCAST MULTICAST MTU:1500 METRIC:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:5687 errors:0 dropped:0 overruns:0 frame:0
TX packets:5687 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:531647 (531.6 KB) TX bytes:531647 (531.6 KB)
wlan0 Link encap:Ethernet HWaddr e0:91:f5:53:47:23
inet addr:192.168.1.66 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: 2602:306:31b6:dbd0:e291:f5ff:fe53:4723/64 Scope:Global
inet6 addr: 2602:306:31b6:dbd0:389a:6c14:8305:81ca/64 Scope:Global
inet6 addr: fe80::e291:f5ff:fe53:4723/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:23561 errors:0 dropped:0 overruns:0 frame:0
TX packets:20483 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:10010457 (10.0 MB) TX bytes:3313915 (3.3 MB)
"
Notice that there is not an IP address for eth0 even though the интерфейс ты существуешь в хардвер address.
Setup on the client ПК, puppypc:
Puppy_Network_Setup
Enter you static IP parameters:
- If you are using a router check your router’s
status page to get these values.
- If you connect directly to your modem you will
need to get these values from your ISP.
Please enter all addresses in dotted-quad decimal
format (xxx.xxx.xxx.xxx). other formats will
not be recognized.
Static IP parameters
IP address: 192.168.1.72
Net Mask: 255.255.255.0
Gateway: 192.168.1.254
DNS parameters
Primary: 192.168.1.254
Secondary: 8.8.8.8
The ethernet интерфейс on the node puppypc is unable to connect to the Интернет. If I add в static IP address of 192.168.1.70 to eth0 on my desktop, HP-Pavilion, I get messages of “unable to resolve host: HP-Pavilion”. There appears to be в conflict between wlan0 and eth0.
What should the configuration of eth0 and wlan0 be for Lubuntu 14.04.3 to allow communication locally between computers, and wireless connection to the Интернет?
Changed client персональный компьютер to HPMini running Lubuntu 14.04.3. Connected ethernet кабель to desktop. Client персональный компьютер booted with ethernet showing instead of its wireless интерфейс. Desktop ifconfig eth0 showed inet: 10.42.0.1, Bcast: 10.42.0.255. The HPMini ifconfig eth0 showed inet: 10.42.0.57, Bcast: 10.42.0.255. DNS Servers 127.0.1.1, and Сеарч Домаин attlocal.net.
The question хан be withdrawn.