Не удалось загрузить образ ядра устройства imx8

я не создал образ ядра Ubuntu с помощью оснастки ядра и оснастки гаджета с помощью snap craft, после прошивки сгенерированного образа на SD-карту и подключения SD-карты к iMX8MP-EVK . ]board плата успешно загружается до U-boot, но после загрузки образа ядра выдает ошибку и прекращает загрузку образа ядра. Пожалуйста, помогите мне найти решение для этого. Пожалуйста, найдите ниже журналы.

Run CMD11 1.8V switch switch to partitions #0, OK mmc1 is current device Run CMD11 1.8V switch 28092928 bytes read in 556 ms (48.2 MiB/s) Booting from mmc ... 60128 bytes read in 79 ms (743.2 KiB/s)
## Flattened Device Tree blob at 43000000    Booting using the fdt blob at 0x43000000    Using Device Tree in place at 0000000043000000, end 0000000043011adf Can't find cec device id=0x3c fail to probe panel device adv7535@3d fail to get display timings probe video device failed, ret -19

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [    0.000000] Linux version 5.4.24-gbabac008e (kuldeep@kuldeep-HP-ENVY-Notebook) (gcc version 9.3.0 (Ubuntu
9.3.0-17ubuntu1~20.04)) #1 SMP PREEMPT Tue Sep 21 16:13:29 IST 2021 [    0.000000] Machine model: NXP i.MX8MPlus EVK board [    0.000000] efi: Getting EFI parameters from FDT: [    0.000000] efi: UEFI not found. [
0.000000] Reserved memory: created CMA memory pool at 0x00000000c4000000, size 960 MiB [    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [   
0.000000] NUMA: No NUMA configuration found [    0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x00000001bfffffff] [   
0.000000] NUMA: NODE_DATA [mem 0x1bf3c6500-0x1bf3c7fff] [    0.000000] Zone ranges: [    0.000000]   DMA32    [mem 0x0000000040000000-0x00000000ffffffff] [    0.000000]   Normal   [mem 0x0000000100000000-0x00000001bfffffff] [    0.000000] Movable zone start for each node [    0.000000] Early memory node ranges [   
0.000000]   node   0: [mem 0x0000000040000000-0x00000000557fffff] [    0.000000]   node   0: [mem 0x0000000056000000-0x00000000923fffff] [    0.000000]   node   0: [mem 0x0000000094400000-0x00000001bfffffff] [    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000001bfffffff] [    0.000000] psci: probing for conduit method from DT. [    0.000000] psci: PSCIv1.1 detected in firmware. [    0.000000] psci: Using standard PSCI v0.2 function IDs [
0.000000] psci: MIGRATE_INFO_TYPE not supported. [    0.000000] psci: SMC Calling Convention v1.1 [    0.000000] percpu: Embedded 24 pages/cpu s58904 r8192 d31208 u98304 [    0.000000] Detected VIPT I-cache on CPU0 [    0.000000] CPU features: detected: ARM erratum 845719 [    0.000000] CPU features: detected: GIC system register CPU interface [    0.000000] Speculative Store Bypass Disable mitigation not required [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1538048 [    0.000000] Policy zone: Normal [    0.000000] Kernel command line: console=ttymxc1,115200 root=/dev/mmcblk1p2 rootwait rw [    0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [    0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [   
0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [    0.000000] software IO TLB: mapped [mem 0xc0000000-0xc4000000] (64MB) [    0.000000] Memory: 5049504K/6250496K available (16508K kernel code, 1450K rwdata, 6480K rodata, 2944K init, 1015K bss, 217952K reserved, 983040K cma-reserved) [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [    0.000000] rcu: Preemptible hierarchical RCU implementation. [    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [    0.000000]  Tasks RCU enabled. [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [    0.000000] GICv3: GIC: Using split EOI/Deactivate mode [    0.000000] GICv3: 160 SPIs implemented [    0.000000] GICv3: 0 Extended SPIs implemented [   
0.000000] GICv3: Distributor has no Range Selector support [    0.000000] GICv3: 16 PPIs implemented [    0.000000] GICv3: no VLPI support, no direct LPI support [    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000 [    0.000000] ITS: No ITS available, not enabling LPIs [    0.000000] irq-imx-gpcv2: EL3 does not support FSL_SIP_CONFIG_GPC_CORE_WAKE, disabling cpuidle. 
0.243045] Bluetooth: SCO socket layer initialized [    0.243859] clocksource: Switched to clocksource arch_sys_counter [    0.244000] VFS: Disk quotas dquot_6.6.0 [    0.244050] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [    0.244198] pnp: PnP ACPI: disabled [    0.249808] thermal_sys: Registered thermal governor 'step_wise' [    0.249811] thermal_sys: Registered thermal governor 'power_allocator' [    0.250175] NET: Registered protocol family 2 [  
0.250462] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear) [    0.250543] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) [    0.250949] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [   
0.251798] TCP: Hash tables configured (established 65536 bind 65536) [    0.251965] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear) [    0.252109] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear) [    0.252364] NET: Registered protocol family 1 [    0.252678] RPC: Registered named UNIX socket transport module. [  
0.252683] RPC: Registered udp transport module. [    0.252688] RPC: Registered tcp transport module. [    0.252694] RPC: Registered tcp NFSv4.1 backchannel transport module. [    0.253032] PCI: CLS 0 bytes, default 64 [    0.253663] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [    0.254088] kvm [1]: IPA Size Limit: 40bits [    0.254989] kvm [1]: GICv3: no GICV resource entry [   
0.254994] kvm [1]: disabling GICv2 emulation [    0.255011] kvm [1]: GIC system register CPU interface enabled [    0.255064] kvm [1]: vgic interrupt IRQ1 [    0.255141] kvm [1]: Hyp mode initialized successfully [    0.260175] Initialise system trusted keyrings [   
0.260281] workingset: timestamp_bits=44 max_order=21 bucket_order=0 [    0.266483] squashfs: version 4.0 (2009/01/31) Phillip Lougher [    0.267090] NFS: Registering the id_resolver key type [    0.267109] Key type id_resolver registered [    0.267115] Key type id_legacy registered [    0.267124] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [    0.267141] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [    0.267481] 9p: Installing v9fs 9p2000 file system support [    0.280242] Key type asymmetric registered [   
0.280248] Asymmetric key parser 'x509' registered [    0.280277] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [   
0.280355] io scheduler mq-deadline registered [    0.280360] io scheduler kyber registered [    0.282648] samsung-hdmi-phy 32fdff00.hdmiphy: failed to get phy apb clk [    0.286733] pwm-backlight lvds_backlight: lvds_backlight supply power not found, using dummy regulator [    0.287271] EINJ: ACPI disabled. [   
0.293706] i.MX8MP clock driver probe done [    0.297571] imx-sdma 30bd0000.dma-controller: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 [    0.297583] imx-sdma 30bd0000.dma-controller: Falling back to sysfs fallback for: imx/sdma/sdma-imx7d.bin [    0.299336] mxs-dma 33000000.dma-apbh: initialized [    0.300887] Bus freq driver module loaded [   
0.306902] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [    0.309332] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 29, base_baud = 5000000) is a IMX [    0.309794] 30880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 30, base_baud = 5000000) is a IMX [   
0.310177] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 31, base_baud = 1500000) is a IMX [    1.339368] printk: console [ttymxc1] enabled [    1.350162] imx-lcdifv3 32fc6000.lcd-controller: No irq get [    1.359106] imx-hdmi-pavi 32fc4000.hdmi-pai-pvi: No pvi clock get [
1.536802] loop: module loaded [    1.548156] imx ahci driver is registered. [    1.556012] spi_imx 30830000.spi: probed [    1.561184] spi-nor spi1.0: n25q256ax1 (32768 Kbytes) [    1.569951] libphy: Fixed MDIO Bus: probed [    1.574869] tun: Universal TUN/TAP device driver,
1.6 [    1.581014] thunder_xcv, ver 1.0 [    1.584288] thunder_bgx, ver 1.0 [    1.587545] nicpf, ver 1.0 [    1.591226] pps pps0: new PPS source ptp0 [    1.600178] libphy: fec_enet_mii_bus: probed [   
1.605486] fec 30be0000.ethernet eth0: registered PHC device 0 [    1.612307] Freescale FM module, FMD API version 21.1.0 [    1.617943] Freescale FM Ports module [    1.621616] fsl_mac: fsl_mac: FSL FMan MAC API based driver [    1.627434] fsl_dpa: FSL DPAA Ethernet driver [    1.631994] fsl_advanced: FSL DPAA Advanced drivers: [    1.636970] fsl_proxy: FSL DPAA Proxy initialization driver [    1.642711] fsl_oh: FSL FMan Offline Parsing port driver [    1.649214] hclge is initializing [    1.652541] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [    1.659769] hns3: Copyright (c) 2017 Huawei Corporation. [    1.665128] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [    1.672184] e1000: Copyright (c) 1999-2006 Intel Corporation. [    1.677968] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [    1.683804] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [    1.689764] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k [    1.696736] igb: Copyright (c) 2007-2014 Intel Corporation. [    1.702346] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [    1.710180] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [    1.716326] sky2: driver version 1.30 [    1.720819] imx-dwmac 30bf0000.ethernet: no reset control found [    1.726901] imx-dwmac 30bf0000.ethernet: User ID: 0x10, Synopsys ID: 0x51 [    1.733706] imx-dwmac 30bf0000.ethernet:     DWMAC4/5 [    1.738533] imx-dwmac 30bf0000.ethernet: DMA HW capability register supported [    1.745683] imx-dwmac 30bf0000.ethernet: RX Checksum Offload Engine supported [   
1.752828] imx-dwmac 30bf0000.ethernet: TX Checksum insertion supported [    1.759536] imx-dwmac 30bf0000.ethernet: Wake-Up On Lan supported [
1.765665] imx-dwmac 30bf0000.ethernet: Enable RX Mitigation via HW Watchdog Timer [    1.773336] imx-dwmac 30bf0000.ethernet: Enabled Flow TC (entries=8) [    1.779701] imx-dwmac 30bf0000.ethernet: Enabling HW TC (entries=256, max_off=256) [    1.787404] libphy: stmmac: probed [    1.793009] VFIO - User Level meta-driver version:
0.3 [    1.800529] dwc3 38100000.dwc3: Failed to get clk 'ref': -2 [    1.807170] dwc3 38200000.dwc3: Failed to get clk 'ref': -2 [    1.814544] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [    1.821089] ehci-pci: EHCI PCI platform driver [    1.825575] ehci-platform: EHCI generic platform driver [    1.831076] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [    1.837283] ohci-pci: OHCI PCI platform driver [    1.841764] ohci-platform: OHCI generic platform driver [    1.847887] usbcore: registered new interface driver usb-storage [    1.853967] usbcore: registered new interface driver usbserial_generic [    1.860518] usbserial: USB Serial support registered for generic [    1.866554] usbcore: registered new interface driver ftdi_sio [    1.872323] usbserial: USB Serial support registered for FTDI USB Serial Device [    1.879664] usbcore: registered new interface driver usb_serial_simple [    1.886214] usbserial: USB Serial support registered for carelink [    1.892327] usbserial: USB Serial support registered for zio [    1.898009] usbserial: USB Serial support registered for funsoft [    1.904037] usbserial: USB Serial support registered for flashloader [   
1.910411] usbserial: USB Serial support registered for google [    1.916354] usbserial: USB Serial support registered for libtransistor [    1.922908] usbserial: USB Serial support registered for vivopay [    1.928936] usbserial: USB Serial support registered for moto_modem [    1.935225] usbserial: USB Serial support registered for motorola_tetra [    1.941865] usbserial: USB Serial support registered for novatel_gps [    1.948238] usbserial: USB Serial support registered for hp4x [    1.954010] usbserial: USB Serial support registered for suunto [    1.959951] usbserial: USB Serial support registered for siemens_mpi [    1.969888] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc@0/30000000.bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0 [    1.984954] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0 [    1.991282] i2c /dev entries driver [    2.004605] imx2-wdt
30280000.watchdog: timeout 60 sec (nowayout=0) [    2.011262] Bluetooth: HCI UART driver ver 2.3 [    2.015723] Bluetooth: HCI UART protocol H4 registered [    2.020870] Bluetooth: HCI UART protocol BCSP registered [    2.026205] Bluetooth: HCI UART protocol LL registered [    2.031350] Bluetooth: HCI UART protocol ATH3K registered [    2.036771] Bluetooth: HCI UART protocol Three-wire (H5) registered [    2.043152] Bluetooth: HCI UART protocol Broadcom registered [    2.048844] Bluetooth: HCI UART protocol QCA registered [    2.054153] EDAC MC: ECC not enabled [    2.059812] failed to register cpuidle driver [    2.064540] sdhci: Secure Digital Host Controller Interface driver [    2.070731] sdhci: Copyright(c) Pierre Ossman [    2.075352] Synopsys Designware Multimedia Card Interface Driver [    2.082295] sdhci-pltfm: SDHCI platform and OF driver helper [    2.088789] mmc0: CQHCI version 5.10 [    2.123455] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA [    2.130941] mmc1: CQHCI version 5.10 [    2.135030] mmc2: CQHCI version 5.10 [   
2.169737] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA [    2.179271] ledtrig-cpu: registered to indicate activity on CPUs [    2.187178] caam 30900000.crypto: device ID = 0x0a16040100000100 (Era 9) [    2.194003] caam 30900000.crypto: job rings = 3, qi = 0 [    2.214322] caam algorithms registered in /proc/crypto [    2.221185] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto [    2.230722] caam_jr 30901000.jr: registering rng-caam [    2.240783] caam-snvs 30370000.caam-snvs: violation handlers armed - non-secure state [    2.249304] usbcore: registered new interface driver usbhid [    2.254909] usbhid: USB HID core driver [    2.259004] mxc-md 32c00000.bus:camera: deferring cap_device device registration [    2.267986] mxc-isi 32e00000.isi: mxc_isi.0 registered successfully [    2.275143] mxc-mipi-csi2-sam 32e40000.csi: 32e40000.csi supply mipi-phy not found, using dummy regulator [    2.284990] mxc-mipi-csi2-sam 32e40000.csi: lanes: 2, hs_settle: 13, clk_settle: 2, wclk: 1, freq: 500000000 [    2.296038] No fsl,qman node [    2.298923] Freescale USDPAA process driver [   
2.303114] fsl-usdpaa: no region found [    2.306954] Freescale USDPAA process IRQ driver [    2.318329] Galcore version 6.4.0.234062 [   
2.438453] hantrodec 0 : module inserted. Major = 236 [    2.444207] hantrodec 1 : module inserted. Major = 236 [    2.451460] hantroenc: HW at base <0000000038320000> with ID <0x80006200> [    2.458410] hx280enc: module inserted. Major <235> [    2.475542] fsl-micfil-dai 30ca0000.micfil: GET IRQ: 50 [    2.480802] fsl-micfil-dai 30ca0000.micfil: GET IRQ: 51 [    2.481713] mmc2: Command Queue Engine enabled [    2.486054] fsl-micfil-dai 30ca0000.micfil: GET IRQ: 52 [  
2.490503] mmc2: new HS400 Enhanced strobe MMC card at address 0001 [    2.495729] fsl-micfil-dai 30ca0000.micfil: GET IRQ: 53 [    2.502558] mmcblk2: mmc2:0001 DG4032 29.1 GiB [    2.510665] imx-wm8960 sound-wm8960: failed to find codec platform device [    2.512024] mmcblk2boot0: mmc2:0001 DG4032 partition 1 4.00 MiB [    2.520763] debugfs: Directory '30ca0000.micfil' with parent 'imx-audio-micfil' already present! [    2.524703] mmcblk2boot1: mmc2:0001 DG4032 partition 2 4.00 MiB [    2.533426] imx-micfil sound-micfil: snd-soc-dummy-dai <-> 30ca0000.micfil mapping ok [    2.539388] mmcblk2rpmb: mmc2:0001 DG4032 partition 3 4.00 MiB, chardev (237:0) [ 
2.547107] imx-micfil sound-micfil: ASoC: no DMI vendor name! [    2.555502]  mmcblk2: p1 p2 [    2.561177] imx-cdnhdmi sound-hdmi: ASoC: failed to init link imx8 hdmi: -517 [    2.570203] imx-cdnhdmi sound-hdmi: snd_soc_register_card failed (-517) [    2.577251] debugfs: Directory '30cc0000.xcvr' with parent 'imx-audio-xcvr' already present! [    2.585782] imx-xcvr sound-xcvr: snd-soc-dummy-dai <-> 30cc0000.xcvr mapping ok [    2.593108] imx-xcvr sound-xcvr: ASoC: no DMI vendor name! [    2.599033] pktgen: Packet Generator for packet performance testing. Version: 2.75 [    2.606972] NET: Registered protocol family 26 [    2.611996] NET: Registered protocol family 10 [
2.617138] Segment Routing with IPv6 [    2.620865] NET: Registered protocol family 17 [    2.625382] Bluetooth: RFCOMM TTY layer initialized [    2.630274] Bluetooth: RFCOMM socket layer initialized [    2.635438] Bluetooth: RFCOMM ver 1.11 [    2.639199] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [    2.644514] Bluetooth: BNEP filters: protocol multicast [    2.649748] Bluetooth: BNEP socket layer initialized [    2.654718] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [    2.660647] Bluetooth: HIDP socket layer initialized [    2.665650] 8021q: 802.1Q VLAN Support v1.8 [   
2.669851] lib80211: common routines for IEEE802.11 drivers [    2.675615] 9pnet: Installing 9P2000 support [    2.679916] tsn generic netlink module v1 init... [    2.684680] Key type dns_resolver registered [    2.689270] registered taskstats version 1 [   
2.693378] Loading compiled-in X.509 certificates [    2.699291] Key type encrypted registered [    2.727463] pca9450 0-0025: Device ID=0x31 [    2.731578] pca9450 0-0025: gpio_intr = 3 [    2.735614] pca9450 0-0025: chip_irq=85 [    2.758372] random: fast init done [   
2.769865] i2c i2c-0: IMX I2C adapter registered [    2.775284] adv7511 1-003d: 1-003d supply avdd not found, using dummy regulator [   
2.782653] adv7511 1-003d: 1-003d supply dvdd not found, using dummy regulator [    2.790009] adv7511 1-003d: 1-003d supply pvdd not found, using dummy regulator [    2.797361] adv7511 1-003d: 1-003d supply a2vdd not found, using dummy regulator [    2.804800] adv7511 1-003d: 1-003d supply v3p3 not found, using dummy regulator [    2.812166] adv7511 1-003d: 1-003d supply v1p2 not found, using dummy regulator [ 
2.820052] adv7511 1-003d: Probe failed. Remote port 'mipi_dsi@32e60000' disabled [    2.881374] it6263 1-004c: Probe failed. Remote port 'lvds-channel@0' disabled [    2.890046] ov5640 1-003c: 1-003c supply DOVDD not found, using dummy regulator [   
2.897411] ov5640 1-003c: 1-003c supply AVDD not found, using dummy regulator [    2.904674] ov5640 1-003c: 1-003c supply DVDD not found, using dummy regulator [    2.955192] ov5640 1-003c: ov5640_read_reg: error: reg=300a [    2.960781] ov5640 1-003c: ov5640_check_chip_id: failed to read chip identifier [    2.968246] i2c i2c-1: IMX I2C adapter registered [    2.981786] i2c i2c-2: IMX I2C adapter registered [    2.987272] imx8mq-usb-phy 381f0040.usb-phy: 381f0040.usb-phy supply vbus not found, using dummy regulator [   
2.997172] imx8mq-usb-phy 382f0040.usb-phy: 382f0040.usb-phy supply vbus not found, using dummy regulator [    3.009137] pwm-backlight lvds_backlight: lvds_backlight supply power not found, using dummy regulator [    3.009324] imx6q-pcie 33800000.pcie: 33800000.pcie supply epdev_on not found, using dummy regulator [    3.023713] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [    3.027865] imx6q-pcie 33800000.pcie: host bridge /pcie@33800000 ranges: [   
3.034241] [drm] No driver support for vblank timestamp query. [    3.040948] imx6q-pcie 33800000.pcie:   No bus range found for /pcie@33800000, using [bus 00-ff] [    3.046932] imx-drm display-subsystem: bound imx-lcdifv3-crtc.0 (ops lcdifv3_crtc_ops) [  
3.055661] imx6q-pcie 33800000.pcie:    IO 0x1ff80000..0x1ff8ffff -> 0x00000000 [    3.063611] imx-drm display-subsystem: bound imx-lcdifv3-crtc.1 (ops lcdifv3_crtc_ops) [    3.070977] imx6q-pcie
33800000.pcie:   MEM 0x18000000..0x1fefffff -> 0x18000000 [    3.078927] imx-drm display-subsystem: bound imx-lcdifv3-crtc.2 (ops lcdifv3_crtc_ops) [    3.086341] imx6q-pcie 33800000.pcie: PLL REF_CLK is used!. [    3.094789] imx_sec_dsim_drv 32e60000.mipi_dsi: version number is 0x1060200 [    3.106785] imx_sec_dsim_drv 32e60000.mipi_dsi: Failed to attach bridge: 32e60000.mipi_dsi [    3.115062] imx_sec_dsim_drv 32e60000.mipi_dsi: failed to bind sec dsim bridge:
-19 [    3.122732] imx-drm display-subsystem: bound 32e60000.mipi_dsi (ops imx_sec_dsim_ops) [    3.130614] imx-drm display-subsystem: bound 32c00000.bus:ldb@32ec005c (ops imx8mp_ldb_ops) [    3.139034] dwhdmi-imx 32fd8000.hdmi: No pavi info found [    3.144367] imx-drm display-subsystem: failed to bind 32fd8000.hdmi (ops dw_hdmi_imx_ops):
-517 [    3.153184] imx-drm display-subsystem: master bind failed: -517 [    3.160696] dwc3 38100000.dwc3: Failed to get clk 'ref': -2 [    3.166397] OF: graph: no port node found in /usb-phy@381f0040 [    3.173490] dwc3 38200000.dwc3: Failed to get clk 'ref': -2 [    3.179426] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [    3.184942] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [    3.192944] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe6c hci version 0x110 quirks 0x0000000001810010 [    3.202386] xhci-hcd xhci-hcd.1.auto: irq 78, io mem 0x38200000 [    3.208304] imx6q-pcie 33800000.pcie: PCIe PLL locked after 0 us. [    3.214989] hub 1-0:1.0: USB hub found [    3.218773] hub 1-0:1.0: 1 port detected [    3.222943] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [   
3.228445] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [    3.236138] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [    3.242720] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [    3.251183] hub 2-0:1.0: USB hub found [    3.254960] hub 2-0:1.0: 1 port detected [  
3.260140] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 5 mkt segment 0 supported-hw 0x20 0x1 [    3.275980] mmc1: CQHCI version 5.10 [   
3.279598] sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO [    3.308361] imx6q-pcie 33800000.pcie: Link up [    3.312740] imx6q-pcie
33800000.pcie: Link up [    3.316060] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA [    3.317109] imx6q-pcie
33800000.pcie: Link up, Gen1 [    3.325750] mx8-img-md: Registered mxc_isi.0.capture as /dev/video0 [    3.329146] imx6q-pcie
33800000.pcie: PCI host bridge to bus 0000:00 [    3.335558] unregister ISI channel: mxc_isi.0 [    3.341691] pci_bus 0000:00: root bus resource [bus 00-ff] [    3.351532] pci_bus 0000:00: root bus resource [io  0x0000-0xffff] [    3.355241] debugfs: Directory '30c30000.sai' with parent 'wm8960-audio' already present! [   
3.357720] pci_bus 0000:00: root bus resource [mem 0x18000000-0x1fefffff] [    3.357742] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400 [    3.366018] debugfs: Directory '30c90000.easrc' with parent 'wm8960-audio' already present! [   
3.372795] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [    3.378863] imx-wm8960 sound-wm8960: wm8960-hifi <-> 30c30000.sai mapping ok [    3.387142] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref] [    3.395090] imx-wm8960 sound-wm8960: snd-soc-dummy-dai <-> 30c90000.easrc mapping ok [    3.400505] pci 0000:00:00.0: supports D1 [    3.407260] imx-wm8960 sound-wm8960: wm8960-hifi <-> 30c30000.sai mapping ok [    3.414907] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold [    3.417132] pci 0000:01:00.0: [1b4b:2b42] type 00 class 0x020000 [    3.418988] imx-wm8960 sound-wm8960: ASoC: no DMI vendor name! [    3.426035] pci 0000:01:00.0: MSI quirk detected; MSI disabled [    3.450010] pci 0000:01:00.0: quirk_disable_all_msi+0x0/0x30 took 23406 usecs [   
3.457291] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [    3.464584] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x000fffff 64bit pref] [    3.472409] pci 0000:01:00.0: supports D1 D2 [    3.476684] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold [    3.483277] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [    3.493662] mmc1: host does not support reading read-only switch, assuming write-enable [    3.509847] pci 0000:00:00.0: BAR 0: assigned [mem 0x18000000-0x180fffff] [   
3.516732] pci 0000:00:00.0: BAR 15: assigned [mem 0x18100000-0x182fffff pref] [    3.524063] pci 0000:00:00.0: BAR 6: assigned [mem 0x18300000-0x1830ffff pref] [    3.531304] pci 0000:01:00.0: BAR 0: assigned [mem 0x18100000-0x181fffff 64bit pref] [
3.539127] pci 0000:01:00.0: BAR 2: assigned [mem 0x18200000-0x182fffff 64bit pref] [    3.547138] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [    3.552383] pci 0000:00:00.0:   bridge window [mem 0x18100000-0x182fffff pref] [    3.553646] imx-cdnhdmi sound-hdmi: ASoC: failed to init link imx8 hdmi: -517 [    3.559916] pcieport 0000:00:00.0: PME: Signaling with IRQ 244 [    3.566779] imx-cdnhdmi sound-hdmi: snd_soc_register_card failed (-517) [    3.591087] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [    3.597728] [drm] No driver support for vblank timestamp query. [    3.603705] imx-drm display-subsystem: bound imx-lcdifv3-crtc.0 (ops lcdifv3_crtc_ops) [    3.611644] imx-drm display-subsystem: bound imx-lcdifv3-crtc.1 (ops lcdifv3_crtc_ops) [    3.619604] imx-drm display-subsystem: bound imx-lcdifv3-crtc.2 (ops lcdifv3_crtc_ops) [  
3.633774] imx_sec_dsim_drv 32e60000.mipi_dsi: version number is 0x1060200 [    3.642782] imx_sec_dsim_drv 32e60000.mipi_dsi: Failed to attach bridge: 32e60000.mipi_dsi [    3.652174] imx_sec_dsim_drv 32e60000.mipi_dsi: failed to bind sec dsim bridge: -19 [    3.660881] imx-drm display-subsystem: bound 32e60000.mipi_dsi (ops imx_sec_dsim_ops) [    3.670878] imx-drm display-subsystem: bound 32c00000.bus:ldb@32ec005c (ops imx8mp_ldb_ops) [    3.681358] mmc1: new ultra high speed SDR104 SDHC card at address 0001 [    3.688294] dwhdmi-imx 32fd8000.hdmi: Detected HDMI TX controller v2.13a with HDCP (samsung_dw_hdmi_phy2) [    3.698024] mmcblk1: mmc1:0001 GB1QT 29.8 GiB [    3.703192] dwhdmi-imx 32fd8000.hdmi: registered DesignWare HDMI I2C bus driver [    3.710530]  mmcblk1: p1 p2 [    3.714539] imx-drm display-subsystem: bound 32fd8000.hdmi (ops dw_hdmi_imx_ops) [
3.722131] [drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 0 [    3.729996] [drm] Cannot find any crtc or sizes [    3.735260] debugfs: Directory '30cb0000.aud2htx' with parent 'audio-hdmi' already present! [    3.743672] imx-cdnhdmi sound-hdmi: i2s-hifi <-> 30cb0000.aud2htx mapping ok [    3.750739] imx-cdnhdmi sound-hdmi: ASoC: no DMI vendor name! [    3.756553] [drm] Cannot find any crtc or sizes [    3.762190] snvs_rtc
30370000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:01 UTC (1) [    3.771818] isi-m2m 32e00000.isi:m2m_device: Register m2m success for ISI.0 [    3.778904] cfg80211: Loading compiled-in X.509 certificates for regulatory database [    3.788423] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [    3.795017] platform regulatory.0: Direct firmware load for regulatory.db failed with error
-2 [    3.803640] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db [    3.816929] ALSA device list: [   
3.819906]   #0: imx-audio-micfil [    3.823308]   #1: imx-audio-xcvr [    3.826541]   #2: wm8960-audio [    3.829602]   #3: audio-hdmi [    3.837644] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [    3.845784] VFS: Mounted root (ext4 filesystem) on device 179:98. [    3.852502] devtmpfs: error mounting -2 [   
3.857063] Freeing unused kernel memory: 2944K [    3.861697] Run /sbin/init as init process [    3.865829] Run /etc/init as init process [    3.869864] Run /bin/init as init process [    3.873914] Run /bin/sh as init process [    3.877831] Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/admin-guide/init.rst for guidance. [    3.891999] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.4.24-gbabac008e #1 [    3.898871] Hardware name: NXP i.MX8MPlus EVK board (DT) [    3.904181] Call trace: [    3.906631]  dump_backtrace+0x0/0x140 [    3.910293]  show_stack+0x14/0x20 [    3.913608]  dump_stack+0xb4/0xf8 [   
3.916923]  panic+0x158/0x324 [    3.919977]  kernel_init+0xec/0x100 [    3.923466]  ret_from_fork+0x10/0x18 [    3.927042] SMP: stopping secondary CPUs [    3.930964] Kernel Offset: disabled [    3.934452] CPU features: 0x0002,2000200c [    3.938459] Memory Limit: none [   
3.941517] ---[ end Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/admin-guide/init.rst for guidance. ]---