Ошибка жесткого диска: print_req_error: критическая ошибка среды, dev sdb, сектор 16128

Я верю, у меня есть жесткий диск USB, это повреждено. Когда я работаю dmesg, это показывает:

[80489.847168] ---[ end trace 66bad045bd32e5be ]---
[80577.323943] usb 2-1.1: new high-speed USB device number 4 using ehci-pci
[80577.434010] usb 2-1.1: New USB device found, idVendor=152d, idProduct=2329
[80577.434016] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[80577.434020] usb 2-1.1: Product: USB to ATA/ATAPI bridge
[80577.434024] usb 2-1.1: Manufacturer: JMicron
[80577.434028] usb 2-1.1: SerialNumber: F8B08539621E
[80577.434862] usb-storage 2-1.1:1.0: USB Mass Storage device detected
[80577.436400] usb-storage 2-1.1:1.0: Quirks match for vid 152d pid 2329: 8020
[80577.436468] scsi host4: usb-storage 2-1.1:1.0
[80578.445148] scsi 4:0:0:0: Direct-Access     MD02500- AVDW-RO          01.0 PQ: 0 ANSI: 2 CCS
[80578.446026] sd 4:0:0:0: Attached scsi generic sg2 type 0
[80578.446441] sd 4:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/233 GiB)
[80578.447457] sd 4:0:0:0: [sdb] Write Protect is off
[80578.447465] sd 4:0:0:0: [sdb] Mode Sense: 28 00 00 00
[80578.448565] sd 4:0:0:0: [sdb] No Caching mode page found
[80578.448574] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[80578.485832]  sdb: sdb1 < sdb5 >
[80578.489329] sd 4:0:0:0: [sdb] Attached SCSI disk
[80581.790218] sd 4:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[80581.790223] sd 4:0:0:0: [sdb] tag#0 Sense Key : Medium Error [current] 
[80581.790225] sd 4:0:0:0: [sdb] tag#0 Add. Sense: Unrecovered read error
[80581.790229] sd 4:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 3f 00 00 00 08 00
[80581.790232] print_req_error: critical medium error, dev sdb, sector 16128
[80584.135828] sd 4:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[80584.135837] sd 4:0:0:0: [sdb] tag#0 Sense Key : Medium Error [current] 
[80584.135843] sd 4:0:0:0: [sdb] tag#0 Add. Sense: Unrecovered read error
[80584.135852] sd 4:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 3f 00 00 00 08 00
[80584.135856] print_req_error: critical medium error, dev sdb, sector 16128
[80584.135867] Buffer I/O error on dev sdb5, logical block 0, async page read
[80584.135875] Buffer I/O error on dev sdb5, logical block 1, async page read
[80584.135880] Buffer I/O error on dev sdb5, logical block 2, async page read
[80584.135885] Buffer I/O error on dev sdb5, logical block 3, async page read
[80584.135890] Buffer I/O error on dev sdb5, logical block 4, async page read
[80584.135941] Buffer I/O error on dev sdb5, logical block 5, async page read
[80584.135961] Buffer I/O error on dev sdb5, logical block 6, async page read
[80584.135977] Buffer I/O error on dev sdb5, logical block 7, async page read

я прочитал эту статью, в которой говорится, что можно вызвать, перераспределяют поврежденные секторы:

$ sudo hdparm --read-sector 16128 /dev/sdb5
/dev/sdb5: Device /dev/sdb5 has non-zero LBA starting offset of 16128.
Please use an absolute LBA with the /dev/ entry for the raw device,   rather than a partition or raid name.   
/dev/sdb5 is probably a partition of /dev/sdb (?)   
The absolute LBA of sector 16128 from /dev/sdb5 should be 32256   
Aborting.

Я потерян с тем, что попробовать рядом с доступом данные из этого диска.
Кто-либо может помочь?

Умная информация ниже:

sudo smartctl --all /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-46-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     MD02500-AVDW-RO
Serial Number:    FXB0XKS96R1E
LU WWN Device Id: 5 0014ee 600ec4c15
Firmware Version: 01.01A01
User Capacity:    250,059,350,016 bytes [250 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Sun Mar 22 16:06:55 2020 GMT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                    was never started.
                    Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                    without error or no self-test has ever 
                    been run.
Total time to complete Offline 
data collection:        ( 6600) seconds.
Offline data collection
capabilities:            (0x7b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                    General Purpose Logging supported.
Short self-test routine 
recommended polling time:    (   2) minutes.
Extended self-test routine
recommended polling time:    (  79) minutes.
Conveyance self-test routine
recommended polling time:    (   5) minutes.
SCT capabilities:          (0x7037) SCT Status supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   100   253   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   183   179   021    Pre-fail  Always       -       1850
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       75
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       3
 10 Spin_Retry_Count        0x0032   100   253   051    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       73
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       70
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       42
194 Temperature_Celsius     0x0022   120   106   000    Old_age   Always       -       27
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       13
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   051    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.