lsblk, не перечисляющий карту с интерфейсом USB

Я уже разрушил карту с интерфейсом USB несколько месяцев назад, на этот раз это немного более дорого, таким образом, я хотел бы восстановить его (в прошлый раз, когда я удалил его, не имея savely удаленный, на этот раз я понятия не имею, почему это - дефект).

Мои две системы Kubuntu не реагируют на палку usb, мои две системы окон не могут обнаружить ее правильно ни (ни восстановить ее, следовательно).
Это ни не показывают в gparted, ни в lsblk. Иногда lsusb распознает его:

Bus 003 Device 004: ID 05dc:a838 Lexar Media, Inc. 
Couldn't open device, some information will be missing
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x05dc Lexar Media, Inc.
  idProduct          0xa838 
  bcdDevice           11.00
  iManufacturer           1 
  iProduct                2 
  iSerial                 3 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              500mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk-Only
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0

Я могу распознать его через dmesg:

[   77.676004] usb 3-3: new high-speed USB device number 4 using xhci_hcd
[   77.809438] usb 3-3: New USB device found, idVendor=05dc, idProduct=a838
[   77.809446] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   77.809450] usb 3-3: Product: USB Flash Drive
[   77.809454] usb 3-3: Manufacturer: Lexar
[   77.809457] usb 3-3: SerialNumber: AADBL26RWXBD0NG2
[   77.826299] usb-storage 3-3:1.0: USB Mass Storage device detected
[   77.826443] scsi host5: usb-storage 3-3:1.0
[   77.826562] usbcore: registered new interface driver usb-storage
[   77.829127] usbcore: registered new interface driver uas
[  100.256875] usb 3-3: reset high-speed USB device number 4 using xhci_hcd
[  105.368403] usb 3-3: device descriptor read/64, error -110
[  120.583302] usb 3-3: device descriptor read/64, error -110
[  120.799303] usb 3-3: reset high-speed USB device number 4 using xhci_hcd
[  120.911288] usb 3-3: device descriptor read/64, error -71
[  121.127280] usb 3-3: device descriptor read/64, error -71
[  121.343233] usb 3-3: reset high-speed USB device number 4 using xhci_hcd
[  121.343320] usb 3-3: Device not responding to setup address.
[  121.547266] usb 3-3: Device not responding to setup address.
[  121.751155] usb 3-3: device not accepting address 4, error -71
[  121.863174] usb 3-3: reset high-speed USB device number 4 using xhci_hcd
[  121.863316] usb 3-3: Device not responding to setup address.
[  122.067232] usb 3-3: Device not responding to setup address.
[  122.271085] usb 3-3: device not accepting address 4, error -71
[  122.271211] usb 3-3: USB disconnect, device number 4
[  122.383077] usb 3-3: new high-speed USB device number 5 using xhci_hcd
[  122.495086] usb 3-3: device descriptor read/64, error -71
[  122.711142] usb 3-3: device descriptor read/64, error -71
[  122.927043] usb 3-3: new high-speed USB device number 6 using xhci_hcd
[  123.039102] usb 3-3: device descriptor read/64, error -71
[  123.255217] usb 3-3: device descriptor read/64, error -71
[  123.471041] usb 3-3: new high-speed USB device number 7 using xhci_hcd
[  123.471218] usb 3-3: Device not responding to setup address.
[  123.675183] usb 3-3: Device not responding to setup address.
[  123.879044] usb 3-3: device not accepting address 7, error -71
[  123.991010] usb 3-3: new high-speed USB device number 8 using xhci_hcd
[  123.991154] usb 3-3: Device not responding to setup address.
[  124.195085] usb 3-3: Device not responding to setup address.
[  124.398957] usb 3-3: device not accepting address 8, error -71
[  124.398989] usb usb3-port3: unable to enumerate USB device

PS: Мне действительно не нужны данные, было бы хорошо для других так или иначе :)